Recycled Electrical & Control Modules Warranty

Business Hours: Monday – Friday, 8:00 a.m. to 5:00 p.m. Central Time (Texas)

Last Updated: January  2026

IMPORTANT NOTICE

This Electrical & Control Module Warranty Policy forms an integral part of the Terms & Conditions of Precision Auto Parts Group LLC (“PAS”). By purchasing, installing, or using any electrical or control module supplied by PAS, the customer acknowledges that they have read, understood, and agreed to be legally bound by this policy.

This policy applies to all electronic components including but not limited to Engine Control Units (ECU), Engine Control Modules (ECM), Powertrain Control Modules (PCM), Transmission Control Modules (TCM), ABS Modules, Body Control Modules (BCM), Totally Integrated Power Modules (TIPM), Fuse Boxes, and similar vehicle electronic systems.

ELECTRICAL COMPONENT WARRANTY

All electrical components supplied by PAS are used, reconditioned, or tested units that have been verified for basic functionality prior to shipment.

This warranty applies only to the original purchaser, for private, non-commercial use, and only to the vehicle in which the component is installed. This warranty is non-transferable.

Warranty coverage applies strictly to the internal electronic functionality of the module and is valid for the duration specified on the invoice.

PAS reserves the right, at its sole discretion, to repair, replace, or provide an equivalent unit in the event of an approved claim.

COMPONENTS COVERED UNDER THIS POLICY

This policy includes, but is not limited to, the following components:

Engine & Drivetrain Electronics

• ECU (Engine Control Unit)

• ECM (Engine Control Module)

• PCM (Powertrain Control Module)

• TCM (Transmission Control Module)

Safety & Body Electronics

• ABS Module / ABS Control Unit

• BCM (Body Control Module)

• TIPM (Totally Integrated Power Module)

• Fuse Box / Power Distribution Module

General Electrical Modules

• Other vehicle electronic control modules and units

WARRANTY VALIDATION REQUIREMENTS

To maintain warranty eligibility, the following conditions must be strictly met:

• Installation must be completed within 10 days of delivery

• Installation must be performed by a qualified technician

• Installation and diagnostic documentation must be submitted within 10 days

• Proper diagnostic procedures must be performed prior to installation

• The root cause of the original issue must be identified and confirmed

Failure to comply will result in voidance of warranty coverage.

DIAGNOSTIC & PROGRAMMING REQUIREMENT (CRITICAL CONDITION)

Electrical components require accurate diagnostic confirmation prior to replacement.

The installer must:

• Perform a full system diagnostic scan

• Verify fault codes and system behavior

• Confirm wiring integrity and power supply

• Ensure no external electrical faults exist

Additionally, many modules require:

• Programming

• Coding

• VIN matching

• Relearn procedures

Failure to properly diagnose or program the unit is not considered a product defect and is not covered under warranty.

NON-COVERED COMPONENTS & SYSTEMS

This warranty does not cover failures caused by:

• Wiring harness faults

• Poor ground connections

• Blown fuses or relays

• Sensor failures

• Voltage spikes or electrical damage

• Battery or charging system issues

• Improper programming or coding

Any issue not directly attributable to internal failure of the module is excluded.

IMPORTANT WARNING

Electrical components are highly sensitive to system conditions. Incorrect diagnosis is one of the most common causes of replacement failure.

PAS shall not be responsible for issues resulting from misdiagnosis, improper installation, or unresolved vehicle system faults.

IN THE EVENT OF A FAILURE (CRITICAL REQUIREMENT)

Under no circumstances should the module be opened, modified, or tampered with.

The customer must contact PAS immediately upon discovery of an issue. Unauthorized actions will result in immediate voidance of warranty.

INSTALLATION & VALIDATION REQUIREMENTS

The installer must:

• Confirm correct part compatibility

• Perform pre-installation diagnostics

• Ensure all wiring and connectors are intact

• Complete all required programming and relearn procedures

• Verify proper system functionality after installation

Failure to follow these steps may result in improper operation and denial of warranty claims.

COMMON CAUSES OF FAILURE (NOT COVERED UNDER WARRANTY)

The following are not covered:

• Incorrect diagnosis

• Failure to program or code module

• Wiring or electrical system faults

• Sensor or actuator failures

• Voltage irregularities

• Installation errors

WARRANTY VOID CONDITIONS

Warranty will be void under the following conditions:

• Installation beyond 10 days of delivery

• Failure to provide documentation

• Unauthorized opening or modification

• Improper installation or programming

• Evidence of electrical damage or misuse

TERMS & CONDITIONS (ENFORCEMENT CLAUSES)

All claims are subject to inspection and approval by PAS.

Warranty coverage is limited strictly to the cost of the part only. PAS shall not be liable for:

• Labor costs

• Diagnostic charges

• Towing or rental expenses

• Loss of use or downtime

All decisions made by PAS shall be final.

IN THE EVENT OF FAILURE

The customer must provide complete documentation, including diagnostic reports and installation records. The part must be returned for inspection prior to resolution.

FINAL NOTE

This policy is designed to ensure proper diagnosis, correct installation, and fair evaluation of all electrical component claims.

For complete warranty terms and policies, please visit:
https://precisionautopartsgroup.com/warranty-policy