Recycled Transmissions Warranty - Precision Auto Parts Group

Business Hours: Monday – Friday, 8:00 a.m. to 5:00 p.m. Central Time (Texas)

Last Updated: January, 2026

IMPORTANT NOTICE

This Transmission Warranty Policy forms an integral part of the Terms & Conditions of Precision Auto Parts Group LLC (“PAS”). By purchasing, installing, or using any transmission supplied by PAS, the customer acknowledges that they have read, understood, and agreed to be legally bound by this policy.

This policy applies to all aspects of the transaction, including product condition, installation, warranty coverage, exclusions, claim requirements, and dispute resolution.

RECYCLED TRANSMISSION WARRANTY

All recycled transmissions supplied by PAS are used OEM, reconditioned, or remanufactured units that have been inspected and tested for functionality prior to shipment.

This warranty applies only to the original purchaser, for private, non-commercial use, and only for the vehicle in which the transmission was originally installed. This warranty is non-transferable.

Warranty coverage is strictly limited to the internal mechanical components of the transmission and is valid for the period specified on the invoice.

PAS reserves the right, at its sole discretion, to repair, replace, or provide a comparable unit in the event of an approved warranty claim. Replacement units may be of equal or lower mileage depending on availability.

MECHANICAL PARTS WARRANTY EXCLUSIONS

This warranty does not cover failures resulting from external or non-internal causes, including but not limited to:

Improper installation or incorrect procedures
Failure to replace required supporting components
Improper fluid levels, contamination, or incorrect fluid type
Overheating or lack of lubrication
Electrical faults or control module issues
Failure to clear diagnostic trouble codes
Vehicle-related issues or pre-existing conditions

Any failure not directly attributable to an internal defect of the transmission will not be covered.

COVERED COMPONENTS (INTERNAL TRANSMISSION ONLY)

Warranty coverage applies strictly to the internal lubricated mechanical components of the transmission, including:

Gear sets
Shafts
Clutch packs (automatic)
Internal pump
Valve body (mechanical function only)
Bearings and internal moving components

No external, electrical, or accessory components are covered unless explicitly stated in writing.

WARRANTY VALIDATION REQUIREMENTS

For the warranty to remain valid, all of the following conditions must be strictly met:

Installation must be completed within 10 days of delivery
Installation must be performed by a qualified technician
Installation documentation must be submitted within 10 days of installation
Proper installation procedures must be followed
The root cause of the original transmission failure must be identified and corrected

Failure to meet any of the above conditions will result in automatic voidance of warranty.

NON-COVERED ACCESSORIES (PROVIDED FOR CONVENIENCE ONLY)

The transmission may include attached accessories for handling convenience. These components are not covered under warranty, including but not limited to:

Sensors and wiring
Solenoids
Torque converter (unless specified)
External wiring harness
Switches and connectors

These components must be inspected and replaced as necessary by the installer.

IMPORTANT WARNING

Transmission compatibility, gear ratios, and electronic configurations must be verified prior to installation. Improper matching or incorrect installation may result in severe drivetrain damage.

PAS shall not be responsible for damage caused by incorrect application, improper installation, or failure to verify compatibility.

IN THE EVENT OF A FAILURE (CRITICAL REQUIREMENT)

Under no circumstances should the transmission be removed, disassembled, or repaired without prior written authorization from PAS.

The customer must contact PAS immediately upon discovering an issue. Unauthorized removal or disassembly will result in immediate voidance of warranty.

RECYCLED TRANSMISSION REQUIRED INSTALLATION CHECKLIST & CORE RETURN PROCEDURES

PLEASE READ BEFORE INSTALLATION

Proper installation is critical to the performance and longevity of the transmission. Many failures occur due to improper installation or failure to address related systems.

The installer is responsible for completing all required procedures prior to operation.

WARRANTY VALIDATION REQUIREMENT (CRITICAL CONDITION)

Warranty validation requires full compliance with the Transmission Installation Checklist, which must be completed and documented.

Failure to complete required steps will result in denial of warranty claims.

INSTALLATION CHECKLIST (MANDATORY COMPLETION REQUIRED)

The installer must ensure that all necessary procedures are performed, including but not limited to:

Identifying and correcting the cause of the original transmission failure
Flushing or replacing transmission cooler and lines
Replacing transmission fluid with manufacturer-recommended fluid
Replacing transmission filter
Verifying proper cooling system function
Ensuring proper electrical connections and control module operation
Clearing all diagnostic trouble codes
Verifying torque converter condition and compatibility
Performing required relearn or programming procedures

Failure to perform these steps may result in contamination, overheating, or improper operation.

COMMON CAUSES OF TRANSMISSION FAILURE (NOT COVERED UNDER WARRANTY)

The following conditions are considered external causes and are not covered under warranty:

Contaminated or unflushed transmission cooler/lines
Improper or low transmission fluid
Overheating due to cooling system failure
Failure to replace or inspect torque converter
Electrical or TCM-related issues
Improper installation or misalignment
Pre-existing drivetrain issues

CORE RETURN PROCEDURES (IF APPLICABLE)

If a core return is required, the following conditions must be met:

The original unit must be returned complete and intact
All fluids must be drained prior to return
The core must be properly packaged to prevent damage
The unit must be returned within the specified timeframe

Failure to comply may result in additional charges or denial of core credit.

WARRANTY VOID CONDITIONS

The warranty will be considered void under any of the following conditions:

Installation beyond the 10-day period
Failure to provide installation documentation
Unauthorized disassembly or modification
Improper installation or maintenance
Use in commercial, racing, or off-road applications
Evidence of overheating, contamination, or misuse

TERMS & CONDITIONS (ENFORCEMENT CLAUSES)

All warranty claims are subject to verification and evaluation by PAS. PAS reserves the right to inspect the part prior to approving any claim.

Warranty coverage is limited strictly to the cost of the part. PAS shall not be liable for:

Labor costs
Towing charges
Rental expenses
Loss of use or downtime

All decisions made by PAS regarding claims shall be final and binding.

IN THE EVENT OF FAILURE

The customer must take all reasonable steps to prevent further damage and must provide all requested documentation, including diagnostic reports, installation records, and maintenance history.

The original part must be returned to PAS for inspection before any resolution is provided.

FINAL NOTE

This policy is designed to ensure fair use, proper installation, and accurate evaluation of all claims. Customers are strongly advised to review all requirements prior to installation.

For complete Terms & Conditions, please visit:
https://precisionautopartsgroup.com/warranty-policy