Re-Manufactured Transmissions Warranty

Business Hours: Monday – Friday, 8:00 a.m. to 5:00 p.m. Central Time (Texas) 
Last Updated: January  2026

IMPORTANT NOTICE

This Re-manufactured Transmission Warranty Policy forms an integral part of the Terms & Conditions of Precision Auto Parts Group LLC (“PAS”). By purchasing, installing, or using any re-manufactured transmission supplied by PAS, the customer acknowledges that they have read, understood, and agreed to be legally bound by this policy.

This policy governs all aspects of the transaction, including product condition, installation requirements, warranty coverage, exclusions, claim procedures, and dispute resolution. These terms remain enforceable regardless of whether a physical signature has been obtained.

RE-MANUFACTURED TRANSMISSION WARRANTY

All re-manufactured transmissions supplied by PAS are rebuilt units that have undergone inspection, reconditioning, and component replacement processes to restore operational functionality.

This warranty applies only to the original purchaser, for private, non-commercial use, and only for the vehicle in which the transmission is originally installed. This warranty is non-transferable.

Warranty coverage is valid for the duration specified on the invoice and begins from the date of delivery (no exceptions).

PAS reserves the right, at its sole discretion, to repair, replace, or provide an equivalent unit in the event of an approved warranty claim. Replacement shall remain the primary remedy.

MECHANICAL PARTS WARRANTY EXCLUSIONS

This warranty does not cover failures caused by conditions external to the internal transmission assembly, including but not limited to:

• Improper installation or failure to follow required procedures

• Failure to replace or flush transmission cooler and lines

• Contaminated, incorrect, or insufficient transmission fluid

• Overheating or lack of lubrication

• Electrical faults, TCM issues, or sensor failures

• Failure to perform required programming or relearn procedures

• Pre-existing drivetrain or vehicle-related issues

Only failures directly attributable to internal defects will be considered.

COVERED COMPONENTS (INTERNAL TRANSMISSION ONLY)

Warranty coverage applies strictly to the internal mechanical components of the re-manufactured transmission, including:

• Gear sets and shafts

• Clutch packs and bands (automatic transmissions)

• Internal pump and valve body (mechanical function)

• Bearings, bushings, and internal lubricated components

All other components are excluded unless specifically stated in writing.

WARRANTY VALIDATION REQUIREMENTS

To maintain warranty eligibility, all of the following conditions must be strictly met:

• Installation must be completed within 10 days of delivery

• Installation must be performed by a qualified and certified technician

• Installation documentation must be submitted within 10 days of installation

• All required installation procedures must be followed

• The root cause of the original failure must be identified and corrected

Failure to meet these conditions will result in voidance of warranty coverage.

NON-COVERED ACCESSORIES (PROVIDED FOR CONVENIENCE ONLY)

Re-manufactured transmissions may include certain attached components for handling convenience. These components are not covered under warranty, including but not limited to:

• Sensors, wiring, and connectors

• Solenoids and electrical components

• Torque converter (unless explicitly included in writing)

• External harnesses and switches

These items must be inspected, serviced, or replaced as required by the installer.

IMPORTANT WARNING

Proper compatibility, including gear ratios, electronic configuration, and system matching, must be verified prior to installation. Incorrect installation or mismatch may result in severe damage to drivetrain components.

PAS shall not be responsible for failures resulting from incorrect application or improper installation.

IN THE EVENT OF A FAILURE (CRITICAL REQUIREMENT)

Under no circumstances should the transmission be removed, disassembled, or repaired without prior written authorization from PAS.

The customer must immediately notify PAS upon discovery of any issue. Unauthorized actions will result in immediate voidance of warranty.

RE-MANUFACTURED TRANSMISSION REQUIRED INSTALLATION CHECKLIST & CORE RETURN PROCEDURES

PLEASE READ BEFORE INSTALLATION

Proper installation is critical to the performance and longevity of a re-manufactured transmission. Even though the unit has been rebuilt, improper installation or contamination can lead to immediate failure.

WARRANTY VALIDATION REQUIREMENT (CRITICAL CONDITION)

Warranty validation is strictly dependent on full compliance with all installation requirements and documentation submission.

Failure to comply with installation procedures will result in denial of warranty claims.

INSTALLATION CHECKLIST (MANDATORY COMPLETION REQUIRED)

The installer must complete all required procedures, including but not limited to:

• Identifying and correcting the cause of original failure

• Flushing or replacing transmission cooler and lines

• Installing new transmission fluid (OEM recommended)

• Replacing transmission filter

• Verifying torque converter condition and compatibility

• Ensuring proper electrical connections and TCM communication

• Clearing all diagnostic trouble codes

• Performing required programming, adaptation, or relearn procedures

Failure to complete these steps may result in contamination, overheating, or improper operation.

COMMON CAUSES OF TRANSMISSION FAILURE (NOT COVERED UNDER WARRANTY)

The following conditions are not covered:

• Contaminated transmission cooler or lines

• Improper or insufficient fluid levels

• Overheating due to cooling system failure

• Failure to replace torque converter where required

• Electrical or programming issues

• Improper installation or misalignment

• Failure to correct pre-existing vehicle issues

CORE RETURN PROCEDURES (IF APPLICABLE)

Where applicable, core return requirements must be followed:

• The original transmission must be returned complete

• All fluids must be drained

• The unit must be properly packaged

• Return must be completed within the specified timeframe

Failure to comply may result in loss of core credit.

WARRANTY VOID CONDITIONS

Warranty will be void under the following conditions:

• Installation beyond 10 days of delivery

• Failure to submit required documentation

• Unauthorized disassembly or modification

• Improper installation or maintenance

• Use in commercial, racing, or off-road applications

• Evidence of overheating, contamination, or misuse

TERMS & CONDITIONS (ENFORCEMENT CLAUSES)

All claims are subject to inspection and approval by PAS. PAS reserves the right to inspect any part prior to approving a claim.

Warranty coverage is limited strictly to the cost of the part. PAS shall not be liable for:

• Labor costs

• Towing or rental expenses

• Loss of use or downtime

All decisions made by PAS shall be final.

IN THE EVENT OF FAILURE

The customer must take reasonable steps to prevent further damage and must provide all required documentation, including diagnostic reports and installation records.

The part must be returned to PAS for inspection prior to any resolution.

FINAL NOTE

This policy is designed to ensure proper installation, fair evaluation of claims, and long-term reliability of re-manufactured transmissions.

For complete warranty terms and policies, please visit:
https://precisionautopartsgroup.com/warranty-policy